Mandatory
Recommended
Other region
Not specified
American NFPA 701
Drapery
METHOD OF TESTING
A burner flame is applied to a vertically oriented textile fabric to determine the flame propagation.
Downloads
American NFPA 701Test method
The test is performed in a test cabinet. A test sample is hung in this cabinet with a pin bar and exposed to a flame. The after flame of the test material and the burning time of the material that falls to the bottom of the cabinet are measured. The weight loss is also measured.
Result
The test material passes or fails the test. To pass, both the weight loss and the burn time have to be limited.
> View all fabrics complying with the American NFPA 701 standard
Related FR standards
American Boston BFD IX 1
A very severe vertical flame test which measures the ignition resistance of a 4" x 12" specimen when exposed to 6" propane torch flame for 10 seconds. After flame, flame propagation distance and afterglow (propagating and non-propagating) are measured.
American CAL 117 Sec.E Part 1 (CS191 53)
The test material is put on a chair simulation and is exposed to a burning cigarette.
American FMVSS 302
A flame is applied to a test specimen to determine the burning behavior of a fabric used for the interior of motor vehicles.
American NFPA 255 / ASTM E 84
The purpose of the test is to provide a comparative measurement of surface flame spread and smoke development of materials with that of a select grade red oak and reinforced cement board under a specific fire exposure conditions.
American NFPA 260A/UFAC Class 1
The test material is put on a chair simulation and is exposed to a burning cigarette.
American NY Port Authority FAR Part 25.853 1992
A vertical flame test which measures the ignition resistance of a 12" x 12" restrain specimen when subjected to 1.5" flame for 12 seconds. Char legnth, after flame and drip burn are measured.
Australian New Zealand AS 1530 part 2
This test is suitable for materials that don't melt or shrink.
Australian New Zealand AS 1530 part 3
Ignitability, flame propagation, heat release and smoke release are determined simultaneously by means of a vertical heat source.
Australian New Zealand AS 3744.2
An assembly of upholstered materials is subjected to a match-flame equivalent to examine its burning behavior.
Australian New Zealand AS NZS 4088.1
An assembly of upholstered materials is subjected to a burning cigarette to examine its burning behavior.
Austrian Önorm B 3825
A flame is applied to a simulated chair to assess the burning behavior of the test fabric.
British BS 5852 source 0, 1,5 (Cigarette, Match) and (Crib 5)
Different ignition sources are applied to a constructed test rig to examine the burning behavior of a test material.
British BS 5867 part 2 type B and C
A flame is applied to a vertically oriented textile fabric to determine the fire behavior.
British BS 7176
Specification for resistance to ignition of upholstered furniture for non-domestic seating by testing composites. This standard refers to the test standards British BS 5852 source 0, 1,5 (Cigarette, Match) and (Crib 5), BS European EN 1021 Part 1 and 2-1 or BS European EN 1021 Part 1 and 2-2, depending on the end-use environment involved.
Canadian CAN ULC S109
A flame is applied to a vertically oriented test fabric to determine the burning behaviour. The test provides a mean to determine the relative response to flame of fabrics under low intensities of fire exposure.
Chinese GB 20286
The burning behavior of fire retarding products and subassemblies in public places is assessed.
European EN 1021 Part 1 and 2
The test fabric is exposed to different ignition sources, namely a burning cigarette and butane flame, to examine its burning behavior.
European EN 13773
A flame is applied to a vertically oriented test fabric to determine the burning behavior.
French NF P92-503,504,505 507 (M1)
Electrical burner test (for 503), complementary rate of flame spread test (for 504) and dripping test (for 505).
German DIN 4102 (B1)
For German DIN 4102 (B1), a material is classified as B1 if it fulfils the requirements of a B2-test and the ‘fire shaft’ test.
IMO FTPC P7 Textiles and Films Fire Test Marine Equipment
A specimen of the fabric for maritime use to be tested is oriented vertically. A flame is applied to it to determine the burning behaviour.
IMO FTPC P8 Upholstered Furniture Fire Test to Marine Equipment
An assembly of upholstery materials for maritime use is subjected to 2 ignition sources: a smoldering cigarette and a flaming source equivalent to a burning match.
Italian UNI 9175 (Classe Uno)
The combustion of upholstered furniture is evaluated in presence of or without flame and/or glow. This gives an indication of the reaction to fire of furniture exposed to a small ignition source.
Japanese JIS L1091
A specimen is subjected to a flame under different conditions. Its burning behavior is observed.
Swiss SNV 198898
The flammability and smoke density are determined, respectively according to SN 198'898 and VKF. The first determines the burning behavior of a vertically oriented fabric, the latter assesses the smoke development of a fabric that is completely burnt down in a test chamber.
Taiwanese CNS 10285 L3196
The flame retardancy properties of thin building materials, thin plywoods and textile products are tested.
Labotex, our test lab for this standard
- Satenrozen 2A, 2550 Kontich, BELGIUM
- +32 3 451 8000
- www.labo-tex.com